Where can I find the 32pin DIL plug for the emulation cable according to the S4emu.doc?
imac
Search found 723 matches
- 14 Nov 2011 17:07
- Forum: Dataman S4
- Topic: 32-pin DIL plug to the Emulation Cable
- Replies: 3
- Views: 3569
- 14 Nov 2011 17:05
- Forum: Dataman S4
- Topic: Need more Information FUNC -> SETUP Menu
- Replies: 8
- Views: 6674
Re: Need more Information FUNC -> SETUP Menu
According to what i read above, i've calculated these new values for my new batteries pack (3600mAh) at 50 Hz: Charge Time ChargeTime = (3600*640*50)/(50*300*3600)-1 = 1,13 so Charge Time = 1 Discharge Time Discharge Time= (18000*640)/(40*3600) = 80, so S4Discharge Time = 80/16=5 Am I right ? Is the...
- 14 Nov 2011 17:05
- Forum: Dataman S4
- Topic: Need more Information FUNC -> SETUP Menu
- Replies: 8
- Views: 6674
Re: Need more Information FUNC -> SETUP Menu
Hi Neil yes the S4 manual link on page 68 has the same deafult settings that i have, hence thats why i cannot understand the text you found that says different Default value for ChargeTime is 11 (0BH) resulting in 300mA, 50Hz Default value for DischargeTime is 28 (1CH) which is internally multiplied...
- 14 Nov 2011 17:04
- Forum: Dataman S4
- Topic: Need more Information FUNC -> SETUP Menu
- Replies: 8
- Views: 6674
Re: Need more Information FUNC -> SETUP Menu
Hi Neil after studying this i am still no further forward in understanding it. I have recently changed the battery pack from the standard 640mah to a 1000mah so was looking into changing the charge and discharge times as discharge times will now be roughly 1/3 longer also i cannot understand the cha...
- 14 Nov 2011 17:02
- Forum: Dataman S4
- Topic: Need more Information FUNC -> SETUP Menu
- Replies: 8
- Views: 6674
Need more Information FUNC -> SETUP Menu
Hello,
I need more Information about the Menu-Points in the Sub-Menu FUNC -> SETUP:
Shutdown Time ?
Charge Time ?
Discharge Time ?
Deep Discharge ?
Norm Discharge ?
Range 00-FF -> hours ? minutes ?
best regards
Lars Weiß
I need more Information about the Menu-Points in the Sub-Menu FUNC -> SETUP:
Shutdown Time ?
Charge Time ?
Discharge Time ?
Deep Discharge ?
Norm Discharge ?
Range 00-FF -> hours ? minutes ?
best regards
Lars Weiß
- 14 Nov 2011 17:02
- Forum: Dataman S4
- Topic: S4 issues
- Replies: 3
- Views: 3642
Re: S4 issues
Hi guys
I have the same problem, and my battery pack is a new one.
When i keep out the battery pack i can charge it with an external charger, then when i replace the pac on the dataman, all is ok for about 8 days.
There is a power consumption when the dataman is switched off ?
martinat
I have the same problem, and my battery pack is a new one.
When i keep out the battery pack i can charge it with an external charger, then when i replace the pac on the dataman, all is ok for about 8 days.
There is a power consumption when the dataman is switched off ?
martinat
- 14 Nov 2011 17:01
- Forum: Dataman S4
- Topic: S4 issues
- Replies: 3
- Views: 3642
S4 issues
Hi There, i have some small issues with my S4, firstly whan it has not been used for a few days & you turn it on, it starts briefly then switches off, it can be reset & will start normally then for a while, only if the charger is connected. secondly the ZIF seems to have a connection problem...
- 14 Nov 2011 17:01
- Forum: Dataman S4
- Topic: PIC16C73A-20/SP
- Replies: 1
- Views: 2439
PIC16C73A-20/SP
Hi, I am finally up and running and have manged to program my very first PIC with the S4 (woo hoo!) I have just done several but had the protection switch turner off. Is it possible to either erase or re-program this PIC. I have been told it is , when I try the programming ends with Verify at VDDmin...
- 14 Nov 2011 17:00
- Forum: Dataman S4
- Topic: Programming order
- Replies: 2
- Views: 2926
Re: Programming order
Hello Neil!
Thanks for your response! I will contact you by E-mail!
Cheers,
Impala
Thanks for your response! I will contact you by E-mail!
Cheers,
Impala
- 14 Nov 2011 17:00
- Forum: Dataman S4
- Topic: Programming order
- Replies: 2
- Views: 2926
Programming order
Hi! I have run into a problem when trying to program a Hitachi 27C1024. This is mentioned on your support page, http://www.dataman.com/WebPages/Support/S4/SupportS4EPROMDefaultProgrammingOrder.aspx but I have no success editing the libraray ROM. The support page mentions 40-pin library version 1.04 ...