Dear Dataman users,
New software has just been posted on our software pages for the Dataman 448Pro2AP super fast industrial gang programmer.
Version 3.53 features the following amendments:
New Device Support
Many new devices have been added in this revision, please download the full device list to verify your chip is supported: Dataman448Pro2APDeviceList.pdf
Major Changes
Credit box version comparison fixed in setup installator, to prevent warning about unsupported credit box detected during installation of PG4UW sw, even if credit box version is supported by sw that is ready to be installed. The warning could occur for special long versions of sw, e.g. "3.51z08"
Other Changes
Added module: AP1 QFN8-1 ZIF SFlash-1b
Added module: AP1 QFN24-1.02 ZIF CY-3
Added module: AP1 QFN28-1.02 ZIF R7F-2
Added module: AP1 QFN68-1.02 ZIF STM32WB-1
Added module: AP1 QFP64-1.02 ZIF ARM-4
Added module: AP1 QFP64-1.02 ZIF LPC-7
Added module: AP1 QFP64-1.02 ZIF R5F-7
Added module: AP1 SOIC14-150 ZIF ISD-1
Added module: AP1 SSOP28-200 ZIF CY-1
Altera EPM570 [TQFP100], improving of ID check routine and pgm parameter assignment
Atmel/Microchip ATmega/tiny series using UPDI interface, Power-on sequence improved
Atmel/Microchip ATmega48PB/88PB/168PB/328PB in ZIF, Read and verify procedures modified
Atmel/Microchip ATtiny3217 [QFN24], Programming enable sequence modified
Cypress S25HL01GTDPMxx01 [SOIC16] (QuadSPI), S25HL512TFAMxx01 [SOIC16] (QuadSPI), Device Verify improved
DIL48/QFP100-1.02 ZIF MSP432-1, update of SW interface
GigaDevice GD25LQ256D [WSON8 5x6], Verifying Status Register modified
Intel E28F016SA [TSOP56], power-up sequence modified
ISSI IS25WP128 [TFBGA24 6x8] (Quad I/O), IS25WP128 [TFBGA24 6x8], IS25LP064A-J [TFBGA24 6x8] (Quad I/O), IS25LP064A-J [TFBGA24 6x8], IS25LP064 [TFBGA24 6x8] (Quad I/O), IS25LP064 [TFBGA24 6x8], IS25CQ032 [TFBGA24 6x8] (Quad I/O), IS25CQ032 [TFBGA24 6x8], IS25LQ032B [TFBGA24 6x8] (Quad I/O), IS25LQ032B [TFBGA24 6x8], IS25LP032A-J [TFBGA24 6x8] (Quad I/O), IS25LP032A-J [TFBGA24 6x8], changed device name and backward project compatibility correction
JEDEC file load, improving of warning information in case of missing checksum section
Microchip PIC16C505, verification procedure improved
Renesas R5F563T6ExFL [LQFP48] Boot mode, power-up modified
Renesas R7F7015653, added verify for ICU-S
Samsung HART-i910, HART-i910Z, programming speed increased
TTL/CMOS 74393, vectors for IC test removed
Winbond W25Q128FWxxG [WSON8 6x5] (QuadSPI), Verifying Status Register - error! listing improved
Bug Fixes
Altera Classic family, power up sequence bug fixed
Atmel/Microchip ATmega/tiny series using UPDI interface, Fixed wrong error message when device is locked
Atmel/Microchip ATmega48/88/168/328/A/V/P/PB, RDY/BSY time-out bug fixed when programming fuse bits
Atmel/Microchip AVRmega64/32U4/48/88/168/328, error message when RDY/BSY time-out occurred bug fixed
Cypress modules AP1 QFN24-1.02 ZIF CY-1, AP1 QFN24-1.02 ZIF CY-2, AP1 QFN56-1.02 ZIF CY-2, AP1 QFN68 ZIF CY-2, AP1 QFP44-1.04 ZIF CY-1, AP1 QFP48-1.02 ZIF CY-1, AP1 QFP64-1.02 ZIF CY-1, AP1 QFP100 ZIF CY-2, detecting bug fixed
GigaDevice GD25LQ256D [WSON8 5x6], Alt+S menu bug fixed
GigaDevice Semic., manufacturer name changed to GigaDevice, project backward compatibility issue fixed
MPS MP288xA, device size bug fixed
ON Semiconductor/Catalyst (CSI) CAT25040, solo verify bug fixed
STMicroelectronics STM8S001J3M, programming option bytes bug fixed
Best regards,
Daniel Smith
New software - Version 3.53
Software update notifications
-
- Posts: 2311
- Joined: 09 Nov 2011 14:36
Return to “Software Update Notifications”
Jump to
- Dataman Products
- Programmers
- Dataman 40Pro
- Software Update Notifications
- Dataman S6
- Software Update Notifications
- Dataman 48Pro2C
- Software Update Notifications
- Dataman 48, 48LV, 48XP and 48UXP
- Software Update Notifications
- Dataman 48Pro2
- Software Update Notifications
- Dataman 48Pro2AP
- Software Update Notifications
- Dataman 448Pro2
- Software Update Notifications
- Dataman 448Pro2AP
- Software Update Notifications
- Dataman 848 and 848XP
- Software Update Notifications
- Dataman 848Pro2
- Software Update Notifications
- Dataman S3
- Dataman S4
- Software Update Notifications
- Dataman 48Pro
- Software Update Notifications
- Dataman 48Pro+
- Software Update Notifications
- Dataman 448Pro
- Software Update Notifications
- Dataman 448Pro+
- Software Update Notifications
- Dataman 448Pro2AP-AU
- Software Update Notifications
- Dataman 848Pro
- Software Update Notifications
- Dataman MEMPro
- Software Update Notifications
- Dataman PIKPro
- Software Update Notifications
- Dataman T51Pro
- Software Update Notifications
- Other Dataman Programmers
- Oscilloscopes
- Dataman 520 Series
- Software Update Notifications
- Dataman 570 Series
- Software Update Notifications
- Dataman 770 Series
- Software Update Notifications
- Waveform Generators
- Dataman 530 Series
- Software Update Notifications
- Validators
- Dataman Vali-Flash
- Dataman Vali-File
- Dataman S4 Validator
- Software Update Notifications
- Other Dataman Products
- Dataman
- Devices and Programming
- General Conversation
- Refurbished Dataman Products
- Programmers
- Other Dataman Products
Who is online
Users browsing this forum: No registered users and 0 guests