New software - Version 3.50

Software update notifications
Dataman (Daniel Smith)
Posts: 2254
Joined: 09 Nov 2011 14:36

New software - Version 3.50

Postby Dataman (Daniel Smith) » 30 May 2019 14:05

Dear Dataman users,

New software has just been posted on our software pages for the Dataman PIKPro PICmicro ISP programmer.

Version 3.50 features the following amendments:

New Device Support
Many new devices have been added in this revision, please download the full device list to verify your chip is supported: DatamanPIKProDeviceList.pdf

Major Changes
Fixed Main Checksum calculation canceled by user break to prevent multiply unwanted calculations (i.e. immediately after breaking calculation)

Other Changes
Analog devices ADuCM362/363, power-up/powed-down procedure modified
Atmel ATmega324PB in ZIF, Power-on/off sequence modified
Cypress CY8C6xxxxx, programming procedure improved
Cypress S6J334CJExxxx [TEQFP176], programming procedure improved
Cypress/Fujitsu/Spansion MB91F57x, programming procedure improved
DIL8/QFN8-5/2 ZIF SFlash-1b, insertion test improved (occasionally might report contact check problem on device pin(s) even if device was inserted correctly)
Exar XRP7724/25, XR9710/11, programming procedure improved
Freescale semic., NXP MC9S08PT32, improved power-up sequence stability
Freescale Semic., NXP S9S12VRxx, added support for new revisions
Microchip PIC16F88, power-up procedure improved
Microchip PIC18F65J90, programming of configuration bits improved
Microchip PIC32MX250F256H [QFN64](2wire JTAG), power-up procedure improved
Micron MT29FxG01xxxxxxx, part names changed (naming convention unified for Micron serial NAND)
NEC/Renesas uPD78F9436, uPD78F9456, insertion test improved
Silicon Laborat. SiM3U154, full chip erase modified
STMicroelectronics STM32L0xx, Option Bytes treatment improved (complementary bytes values are not longer forced on read, default values after device selection matched with reference manual)
STMicroelectronics STM32L4xx, PCROP and WRP areas setting changed - area start and end addresses are expected now (was area first page and last page start offsets)
Texas Instruments BQ26100, programming procedure of KEY and LOCKKx modified

Bug Fixes
Analog devices ADuCM362/363, insertion test bug fixed
Atmel AT90S(LS)2333/4433 [TQFP32], ID check error 1Eh 12h 03h bug fixed, device fail bug fixed
Atmel CFG, bug fixed in list of supported file formats
Atmel/Microchip ATSAML21/ATSAML22/ATSAMD51/ATSAM4LC series, programming and verification of some bits of User Row bug fixed
Cypress/Spansion S25FL256LxxMxx00 [SOIC16] (Quad I/O), Programming Registers(SR1NV,CR1NV,CR2NV,CR3NV) fixed
Intel/Numonyx NOR flash with POF support, bug fixed in list of supported file formats
Microchip PIC16F1776 [UQFN28], device ID fixed
Microchip PIC16F1946, PICmicro checksum calculation bug fixed
Micron MT28EW128ABA1LPN0 [VFBGA56], Loading programming file bug fixed
Micron/Numonyx serial flash with POF support, bug fixed in list of supported file formats
Nuvoton NUC230/240 family, LDROM size bug fixed
NXP LPC23xx [LQFP144], Power-Up sequence bug fixed
Silicon Laborat./Sigma Designs SD3502A, ZM5202 (ISP) (Custom-01), programming bug fixed
STMicroelectronics BlueNRG-132 [QFN32], EDevOpt Fatal Error bug fixed
STMicroelectronics STM32L4xx, main memory blank check problem fixed
Winbond W25Q16FWxxxQ, Verifying Status Register - error! fixed

Best regards,

Daniel Smith

Return to “Software Update Notifications”

Who is online

Users browsing this forum: No registered users and 0 guests