New software - Version 3.53

Software update notifications
Dataman (Daniel Smith)
Posts: 2254
Joined: 09 Nov 2011 14:36

New software - Version 3.53

Postby Dataman (Daniel Smith) » 31 Oct 2019 10:59

Dear Dataman users,

New software has just been posted on our software pages for the Dataman PIKPro PICmicro ISP programmer.

Version 3.53 features the following amendments:

New Device Support
Many new devices have been added in this revision, please download the full device list to verify your chip is supported: DatamanPIKProDeviceList.pdf

Major Changes
Credit box version comparison fixed in setup installator, to prevent warning about unsupported credit box detected during installation of PG4UW sw, even if credit box version is supported by sw that is ready to be installed. The warning could occur for special long versions of sw, e.g. "3.51z08"

Other Changes
Altera EPM570 [TQFP100], improving of ID check routine and pgm parameter assignment
Atmel/Microchip ATmega/tiny series using UPDI interface, Power-on sequence improved
Atmel/Microchip ATmega48PB/88PB/168PB/328PB in ZIF, Read and verify procedures modified
Atmel/Microchip ATtiny3217 [QFN24], Programming enable sequence modified
Cypress S25HL01GTDPMxx01 [SOIC16] (QuadSPI), S25HL512TFAMxx01 [SOIC16] (QuadSPI), Device Verify improved
DIL48/QFP100-1.02 ZIF MSP432-1, update of SW interface
GigaDevice GD25LQ256D [WSON8 5x6], Verifying Status Register modified
Intel E28F016SA [TSOP56], power-up sequence modified
ISSI IS25WP128 [TFBGA24 6x8] (Quad I/O), IS25WP128 [TFBGA24 6x8], IS25LP064A-J [TFBGA24 6x8] (Quad I/O), IS25LP064A-J [TFBGA24 6x8], IS25LP064 [TFBGA24 6x8] (Quad I/O), IS25LP064 [TFBGA24 6x8], IS25CQ032 [TFBGA24 6x8] (Quad I/O), IS25CQ032 [TFBGA24 6x8], IS25LQ032B [TFBGA24 6x8] (Quad I/O), IS25LQ032B [TFBGA24 6x8], IS25LP032A-J [TFBGA24 6x8] (Quad I/O), IS25LP032A-J [TFBGA24 6x8], changed device name and backward project compatibility correction
JEDEC file load, improving of warning information in case of missing checksum section
Microchip PIC16C505, verification procedure improved
Renesas R5F563T6ExFL [LQFP48] Boot mode, power-up modified
Renesas R7F7015653, added verify for ICU-S
Samsung HART-i910, HART-i910Z, programming speed increased
TTL/CMOS 74393, vectors for IC test removed
Winbond W25Q128FWxxG [WSON8 6x5] (QuadSPI), Verifying Status Register - error! listing improved

Bug Fixes
Altera Classic family, power up sequence bug fixed
Atmel/Microchip ATmega/tiny series using UPDI interface, Fixed wrong error message when device is locked
Atmel/Microchip ATmega48/88/168/328/A/V/P/PB, RDY/BSY time-out bug fixed when programming fuse bits
Atmel/Microchip AVRmega64/32U4/48/88/168/328, error message when RDY/BSY time-out occurred bug fixed
GigaDevice GD25LQ256D [WSON8 5x6], Alt+S menu bug fixed
GigaDevice Semic., manufacturer name changed to GigaDevice, project backward compatibility issue fixed
MPS MP288xA, device size bug fixed
ON Semiconductor/Catalyst (CSI) CAT25040, solo verify bug fixed
STMicroelectronics STM8S001J3M, programming option bytes bug fixed

Best regards,

Daniel Smith

Return to “Software Update Notifications”

Who is online

Users browsing this forum: No registered users and 0 guests